How to Remove and Also Replace a Bath Tub
How to Remove and Also Replace a Bath Tub
Blog Article
They are making a few good points regarding How to Install a Bathtub overall in this content down the page.
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Mounting a tub isn't exactly brain surgery, however it does require strong plumbing, carpentry, and also often, tiling skills. Changing an old tub with a new one is additionally a moderately hard job. If the old tub is conveniently easily accessible, the project can relocate speedily; if you need to open a wall surface to remove the old bathtub and place the new bathtub, the job is much harder. In either situation, the project is within a residence handyman's skills, although you will certainly need a helper to vacate the old tub as well as embeded in the new one. See to it you have certified yourself for the job as well as are comfortable trying it. Instead of working with a specialist to take control of a halfway-completed job, it is far better to think about using one before you start. Chances are you might need an expert plumber to make tube links.
This short article will certainly help you set up a brand-new bathtub in your washroom if you have actually currently bought a brand-new bathtub and do not need to alter the setup of your previous water supply pipelines.
Your devices and product checklist ought to consist of the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water supply. After doing so, turn on the taps to drain any water remaining in the system. The process of getting rid of the existing faucets can be rather troublesome because of the restricted access that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a fabric ready for the remaining water that will come from the pipes. As soon as the supply pipelines have actually been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the solitary faucets from turning during this process. Once the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any old sealing substance.
Prior to carrying on to fit the new taps, contrast the pipeline links on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the tap and the other end gives a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, place the tap in the mounting opening in the bath/basin making certain that the washers are in area in between the tap and also the sink. Safeguard the faucet in place with the manufacturer given backnut. As soon as the tap is securely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal faucet ports. The former kind must be linked to the tap finishes first, tightening just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Installing the Bath tub
Utilizing the two wood boards under its feet, put the bathtub in the needed position. The wood boards are valuable in evenly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 little points.
The following goal is to make certain that the tub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the bathtub up until the spirit level reviews level.
To mount taps, fit all-time low of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression join; after that do the exact same for the other tap.
Activate the water system and inspect all joints and new pipework for leakages as well as tighten them if essential. Fill up the bath tub and additionally check the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as defined in the producer's user's manual. Tiling and sealing around the bath tub ought to wait till the bathtub has actually been made use of at least when as this will settle it right into its final setting.
Planning for the Installation
First of all, the sustaining frame supplied with the bathroom should be fitted (if needed) according to the maker's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is necessary to make sure that if the tap features a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets unit to avoid stress on the bath tub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you make use of all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its last placement.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to break a stiff seal, causing the water to penetrate the wall between the bath and the tiling, leading to complications with wetness and also feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your fixtures and also installations. They are offered in tubes as well as cartridges, as well as are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always fill up the tub with water before sealing, to allow for the movement experienced when the bathtub remains in usage. The sealer can split relatively early if you do not consider this motion before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally conveniently readily available on the market. It is recommended to fit the tiles making use of waterproof or water resistant sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a serious reader on Tools You Need to Install a New Bathtub , I assumed sharing that excerpt was a good thing. If you please take a moment to promote this write-up if you enjoyed reading it. Thanks a lot for taking the time to read it.
Book Today
Report this page